[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/bbcode.php on line 483: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/prime_links.php on line 131: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/prime_links.php on line 132: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/prime_links.php on line 131: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /includes/prime_links.php on line 132: preg_replace(): The /e modifier is no longer supported, use preg_replace_callback instead
[phpBB Debug] PHP Warning: in file /feed.php on line 173: Cannot modify header information - headers already sent by (output started at /includes/functions.php:3791)
[phpBB Debug] PHP Warning: in file /feed.php on line 174: Cannot modify header information - headers already sent by (output started at /includes/functions.php:3791)
offroadTB.com Offroad Trailblazers and Envoys 2013-09-30T03:28:25-04:00 https://forums.offroadtb.com/feed.php?f=76&t=2409 2013-09-30T03:28:25-04:00 2013-09-30T03:28:25-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=88313#p88313 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
You'll notice that the CB mount is zip tied, that's because the flex finally work hardened the metal enough that it cracked and started peeling away. I also noticed some rust in the break, which means it was probably starting to break for a long while.

Image



After some consideration, I figured I'd go completely overkill and build a new mount out of 3/16" steel. The top plate was drilled, ground, and welded for the mount and the ground just like the original. But I wanted to do something a bit more fun.
I've been playing with hammer shaping steel for awhile and after this I've established that I need to build a small forge cause I really do enjoy hammer forming metal.

I cut out the mount plate and then I cut out the wrap around shape for the "claw" reinforcement. I wrapped it around the flat mount plate and then tacked it into place with probably a dozen good tacks. Then I burned it in pretty good and started heating up the entire piece to white hot. Then with a ball peen and a few pieces of rod and other chunks of iron I pounded it out to the shape I wanted.

James02 helped a lot with the process, holding this and that and trusting me not to burn him. I couldn't have done this without his help. A ton of thanks goes to him.


At the end I cut off the old mount and welded on the new mount. It barely moves at all and I was really surprised at how much of the flex was because of the sheet metal.

After hammer forming, a quick workover with a bastard file and a flap disk and everything was to my liking. I'm considering doing a dual CB antennae just cause I had so much fun making this.

Image
Image

Statistics: Posted by v7guy — Mon Sep 30, 2013 3:28 am


]]>
2013-08-16T00:46:03-04:00 2013-08-16T00:46:03-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=84478#p84478 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
The hardest part of the A/C clutch bearing was getting the snap ring out of the center of the pulley so you could remove the pulley. After I grabbed the $17 snap ring pliers that were a little longer to replace the cheapie $10 ones it was pretty straight forward. After that and the idler pulley (and previously the power steering pump) my motor was pretty quiet again.

The light for the switches wasn't bad. I took some pics.

I got the bulbs from DNW1-DW10 or 560-DNW1DW10




you'll notice the position of the clips, you want to pry up in those areas

Image



Then you'll cut the sticker, and slide open the tabs I'm pointing at with a small screwdriver or a prying tool.

Image



When you get it serperated you'll see this and need to pry these tabs I'm pointing at to release the circuit board.

Image



Then you'll start prying it open, but there will be a good bit of resistance from the ribbon connectors The black circle on the underside of the board is the light bulb. It needs to twist out and then it's pulled through the bottom of the board.

Image
Image
Image



I had to shave just the tiniest sliver from the bulb to get it to twist on. We're talking a thin thin thin slice.

Image


Installed on the board.

Image

Statistics: Posted by v7guy — Fri Aug 16, 2013 12:46 am


]]>
2013-08-16T00:21:49-04:00 2013-08-16T00:21:49-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=84475#p84475 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>

some quick pics I took. I didn't make a write up cause hatchet over on GMTnation did a fine job. you can find it


Image

Image

Image

Image

Image

Statistics: Posted by v7guy — Fri Aug 16, 2013 12:21 am


]]>
2013-08-05T12:44:27-04:00 2013-08-05T12:44:27-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=83191#p83191 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>

Statistics: Posted by v7guy — Mon Aug 05, 2013 12:44 pm


]]>
2013-07-15T10:47:12-04:00 2013-07-15T10:47:12-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=81587#p81587 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>



Made up a hi lift mount. Just some plate and a half inch bolt with a sleeve welded in. Then holes drilled for the U bolts to bolt it to the roof rack.







Put on roof lighting using some BLAZER brand lights. Ran the wires along the tube and then down through the roof under the rail cap through a drilled hole. They work reasonably well and are an improvement.






relocated front and rear diff breather. Rear diff breather is at the gas filler.





Installed ventshade window pieces.






started cutting the body for tire clearance and to prep for a rear bumper. Wanted to keep the cabin vent so I relocated it.





Statistics: Posted by v7guy — Mon Jul 15, 2013 10:47 am


]]>
2013-03-16T03:26:06-04:00 2013-03-16T03:26:06-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=73464#p73464 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]> viewtopic.php?f=28&t=4033


Image

Statistics: Posted by v7guy — Sat Mar 16, 2013 3:26 am


]]>
2013-02-27T06:20:00-04:00 2013-02-27T06:20:00-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=72072#p72072 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
Image

Statistics: Posted by v7guy — Wed Feb 27, 2013 6:20 am


]]>
2012-12-06T03:13:16-04:00 2012-12-06T03:13:16-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=67916#p67916 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
I ended up getting some 1 x 1 x 1/8" tube 48" long. Drilled holes for some 3/8" bolts after I sleeved the bolt holes with some round tube and capped the ends of the square tube. Then I painted them inside and out. The 3/8" bolts mounted through some 3/16" plate that was cut to fit inside the stock rails. It was all tightened down with some lock washers with loctite on the nuts. The roof rack was bolted to the steel cross bars with some 5/16" u bolts that use lock washers. I can grab the rack and shake the whole truck. Seems pretty solid.


Image
Image
Image
Image

Statistics: Posted by v7guy — Thu Dec 06, 2012 3:13 am


]]>
2012-12-03T04:59:41-04:00 2012-12-03T04:59:41-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=67777#p67777 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
Image



Thread here...

Statistics: Posted by v7guy — Mon Dec 03, 2012 4:59 am


]]>
2012-11-27T01:31:18-04:00 2012-11-27T01:31:18-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=67481#p67481 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
The CB is grounded to the body through the guard itself. Build thread

Image
Image
Image
Image

Statistics: Posted by v7guy — Tue Nov 27, 2012 1:31 am


]]>
2012-06-19T09:04:54-04:00 2012-06-19T09:04:54-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=58787#p58787 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]> viewtopic.php?f=15&t=3283

Statistics: Posted by v7guy — Tue Jun 19, 2012 9:04 am


]]>
2012-01-19T03:04:46-04:00 2012-01-19T03:04:46-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=48109#p48109 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
I've had a tremendous amount of issues with the CV boots. This seems mostly to be a result of the manufacturers currently using a 3 rib boot instead of the old 5 rib boot, this change has happened sometime in the 4th quarter of 2011.
The end result was to replace the boot with a flexible alternative. I've never had any luck with the "split boot" solutions so I tried a dorman 614-004. I've got about three weeks on it and have seen no problems. The stock boots and the boots on the aftermarket shafts failed within 4 days.
You can find a thread on the solution
Here's what I did...

pulled off the old clamp

Image


took off the snap ring

Image

removed the bearings

Image

axle with no bearings

Image

removed the boot

Image

pulled the silicone boot down past the groove in the axle for the stock boot (the silicone boot is longer and needs more space).
Image

clamped it

Image

put the bearing and snap ring back on the axle after it was cleaned and regreased with CV grease

Image

the directions in the silicone boot box said you needed to retain the rubber piece on the tripot. This piece doesn't exist on the aftermarket axles and you cant use the stock piece because the aftermarket tripots are a different shape than stock

Image
Image

so i cut the after market boot to retain the rubber piece that goes around the tripot, cleaned both up and put a dab of silicone to help hold it in place on the tripot.

Image

I became a little worried about the sharp edges of the clamp so I wrapped some electrical tape around it.

Image
Image

new boot stretched... plenty of flex
Image


Here's some pics of the difference between the stock and aftermarket axles. If you're replacing the boot on a stock shaft know that you have to remove a second ring before you can remove the stock boot.


Image
Image

Statistics: Posted by v7guy — Thu Jan 19, 2012 3:04 am


]]>
2011-12-27T04:00:29-04:00 2011-12-27T04:00:29-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=46685#p46685 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
The 89 springs and marks 3" lift with only a skid plate has been a bit problematic concearning CV boots. To date I've tried the stock boots that I experienced a small hole in. They also slipped off the inner (tripot) CV joint twice. The duralast reman cv boot ripped in approx 250 miles. The cardone axle/half shaft had the boot rip in approx 250 miles. The duralast and the cardone appear to be identical when compared side by side.

All the boots failed in the same fashion. The middle rib developed a small hole, then the hole thing rapidly became two pieces. The stock piece seemed to hold up the best, but there is still a hole.

I'm currently looking for alternative boots and I believe with 89 springs and the markmc 3" lift i am at or beyond the limit. I believe i experienced a brief lock up going down an incline at lock.

Obviously more weight on the front end would help, but I'm confident this is as high as we can go without dropping the diff, getting custom CVs or swapping to a live axle.

Statistics: Posted by v7guy — Tue Dec 27, 2011 4:00 am


]]>
2011-12-19T07:14:05-04:00 2011-12-19T07:14:05-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=46194#p46194 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>
Here's the break down




Part Number Part TypePrice EACore EA QuantityTotal
2004 CHEVROLET TRAILBLAZER 4.2L L6 DOHC
ACDELCO215454 (215-454)Air Pump$ 182.79$ 0.001$ 182.79
CARDONE SELECT661345 (66-1345)CV Half Shaft Assembly$ 45.79$ 0.001$ 45.79
MOOGK200270Control Arm Bushing$ 16.33$ 0.001$ 16.33
MOOGK6664Ball Joint$ 56.79$ 0.002$ 113.58
MOOGK200271Control Arm Bushing$ 10.92$ 0.001$ 10.92
MOOGK200269Control Arm Bushing$ 15.16$ 0.002$ 30.32
MOOGK200270Control Arm Bushing$ 16.33$ 0.001$ 16.33
MOOGK6663Ball Joint$ 45.79$ 0.001$ 45.79
MOOGK200272Control Arm Bushing$ 10.86$ 0.002$ 21.72
MOOGK200271Control Arm Bushing$ 10.92$ 0.001$ 10.92
TIMKEN513188Axle Bearing and Hub Assembly$ 140.79$ 0.002$ 281.58
2007 CHEVROLET SILVERADO 2500 HD 6.0L V8
MOOGES3609Tie Rod End$ 48.79$ 0.002$ 97.58
MOOGES3488Tie Rod End$ 32.79$ 0.002$ 65.58

Statistics: Posted by v7guy — Mon Dec 19, 2011 7:14 am


]]>
2011-11-20T04:34:17-04:00 2011-11-20T04:34:17-04:00 https://forums.offroadtb.com/viewtopic.php?t=2409&p=44517#p44517 <![CDATA[Re: v7guy's Build - 2004 Chevrolet Trailblazer LS]]>

Went and picked up some 3/16 steel and cut out an oil pan skid plate. First time I worked with anything this thick... assumed it wouldn't warp when welded because it was good and thick. Ended up pounding on it with a 5lb sledge to straighten it out. Guess you always gotta space out the ole welds. It bolts on and looks like a skid plate.

Radiator skid next... I'm going to have to weld each piece since I can't bend 3/16... I'll be be sure to keep the heat to a minimum.

Statistics: Posted by v7guy — Sun Nov 20, 2011 4:34 am


]]>