Offroad Trailblazers and Envoys

Poor-boy radiator guard

Any special projects involving a decent amount of fab work (bumpers, sliders, roof racks, etc)

by bgwolfpack » Fri Sep 25, 2009 1:15 pm

When I first got this TV and found this site I needed to do a mod, any mod. So I took the front bumper cover off and cleaned and painted everything real nice. Looked good, wife wouldn't shut up about how stupid she thought it looked, so back it went on. But in the mean time I realized how far down the radiator fell in regards to the height of the TV and it's frame. I knew I could purchase a guard for it from the vendor area but that's no fun(and can't afford it right now).

So this is my poor-boy mod. I still like it. Comments welcome :coffee:
Attachments
img_4904 (2).jpg
(243.3 KiB) Downloaded 61 times
img_4900 (2).jpg
(232.92 KiB) Downloaded 61 times
bgwolfpack
Veteran
 
Posts: 1794
Joined: Fri Sep 18, 2009 7:19 pm
Name: Randy
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD

by The Roadie » Fri Sep 25, 2009 1:18 pm

Cool idea. If you could only extend some tubing from that back to the front crossmember you would have a way to divert force that could push both brackets back. I wish I had done that to my radiator skid plate after hitting a very tall rock.
User avatar
The Roadie
Founder
 
Posts: 5011
Joined: Mon Sep 07, 2009 11:29 pm
Location: CA, Vista, San Diego County
Name: Bill Carton
Vehicle Year: 2004
Vehicle: GMC Envoy
DriveTrain: 4WD w/ G80
Rank: Expedition Guide

by Philberto » Fri Sep 25, 2009 1:30 pm

I love the poor-boy mods! Awesome work, I may just copy that if you don't mind.
My Build Thread | 2006 Trailblazer LS Desert Camping Edition **SOLD**
2013 Nissan Xterra S "ReXterra"
User avatar
Philberto
Lifer
 
Posts: 2046
Joined: Fri Sep 11, 2009 5:30 pm
Location: CA, Oxnard
Name: Philip Cruz
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD
Rank: Offroad Rated

by bobbyblaze » Sat Sep 26, 2009 12:48 am

That's a great idea. I would like to refer to that as a thinkin' mans mod cause you was thinkin' that you don't wanna' smash stuff down there.

Is that scedule 40 pipe ? I like Roadie's idea about linking that to the crossmember to spread the force of a hit. Dosen't look like it would be too hard if you weld or know someone who does.
Time. . .is my greatest enemy.
User avatar
bobbyblaze
Trail-Blazer
 
Posts: 343
Joined: Thu Sep 10, 2009 10:31 pm
Name: bb
Vehicle Year: 2002
Vehicle: Other Vehicle
DriveTrain: 4WD
Rank: Offroad Rated

by Gordinho80 » Sat Sep 26, 2009 10:37 pm

Nice work, wolf... Always cool to see the custom mods like this! :cheers:
Mario - Build Thread
User avatar
Gordinho80
Lifer
 
Posts: 2787
Joined: Tue Sep 08, 2009 9:27 am
Location: NJ, Jackson
Name: Mario Almeida
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD

by fishsticks » Sun Apr 11, 2010 4:13 pm

I thought this was such a neat idea that I decided to run with it.... here's what I came up with.

DISCLAIMER: Amateur welder, didn't have gas so I used flux core wire. You're going to see some ugly looking welds. Also, some of my pictures didn't turn out... :(


I drilled and fit my 3' section of pipe like bgwolfpack did. Then I cut a 16" section of 3/16"x1" steel and drilled holes to match the front oil pan skid plate holes. Bolted it in and mocked up some 1/2" steel rod. I believe my center sections came out to be about 14" before bending.

Then I used my precision bender:

Image

... and bent the rods gradually. I test fit them after each bit until I got the angle I wanted. Once I was happy with the fit I marked my attachment points while under the truck, then welded the center supports to the rear plate.

Image

...and then to the front pipe.

Image

Yes, that is galvanized pipe. Yes I realize the danger present in welding galvanized metal. I hit the area I was welding with a grinder first. We also had some serious wind yesterday, and I took advantage of it.

After that I test fit the unit on the truck. Success! (picture didn't turn out). I then ate some corndogs.

Image

...because proper nutrition is important to your health. :coffee2:

Next came the outer supports.

Image

I added some 22 gauge sheet metal to the frame for some extra protection. This is where my welding skills failed me... I really made a mess of attaching it to the frame.

Here it is after the first coat of paint.

Image

Image

It's ugly, but I jumped on the thing a few times (I'm about 210lbs) and it didn't flinch.


On the truck (sorry the lighting in these are terrible):

Image

Image

Image


In conclusion, it's ugly as sin, but under my truck so I'm not worried about it. Obviously I'm not going to use it as a jack point or be landing my truck on it. It makes me feel a little better about my radiator though.

Suggestions welcome.
11 Silverado LTZ - 6.2L/6l80, 2/3 drop, self tuned
85 Hilux - 3RZ, dual cases, caged, 40s, chromo everything
02 TrailBlazer LTZ - 35s, lockers, balls - Gone but not forgotten - Build
User avatar
fishsticks
Moderator
 
Posts: 4356
Joined: Thu Apr 01, 2010 11:30 pm
Location: WA, Vancouver
Name: Donny
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD w/ Aftermarket Locker
Rank: Extreme Offroader

by Gordinho80 » Sun Apr 11, 2010 4:31 pm

Not bad... I wish I could weld!
Mario - Build Thread
User avatar
Gordinho80
Lifer
 
Posts: 2787
Joined: Tue Sep 08, 2009 9:27 am
Location: NJ, Jackson
Name: Mario Almeida
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD

by MrSmithsTB » Sun Apr 11, 2010 5:23 pm

Nice work! Always better to be proud of the imperfections that you created than to pay for the perfections someone else did.
back in the saddle
TB BUILD
User avatar
MrSmithsTB
Veteran
 
Posts: 1756
Joined: Thu Sep 10, 2009 2:28 pm
Location: EHT, NJ
Name: Bob
Vehicle Year: 2006
Vehicle: Other GMT360/370
DriveTrain: AWD w/ G80
Rank: Offroad Rated

by Trail X » Sun Apr 11, 2010 9:07 pm

Very nice! It will at least give you a little safety factor before you run your nose into something... now your radiator end cap isn't the first thing you bash into.

You could clean up your spatter with a little time with the grinder ya know... an ugly weld doesn't have to stay ugly.
8-) Build Thread | ExPo Build | YouTube Videos
Not all who wander are lost. -Tolkien
User avatar
Trail X
Founder
 
Posts: 9935
Joined: Mon Sep 07, 2009 10:22 pm
Location: VA, Roanoke
Name: James Downing
Vehicle Year: 2005
Vehicle: Chevrolet TrailBlazer
DriveTrain: 4WD w/ Aftermarket Locker
Rank: Expedition Guide

by fishsticks » Sun Apr 11, 2010 9:55 pm

Thanks for the kind words folks.

Welding seems to be an exercise in patience more than anything. I had trouble not blowing through the sheet metal and started to lose that patience. Sloppy welds were the result. I ran outta time on Sat...I'll probably go back and grind on it some more later. Also, there are two holes in the front of the cross member that I'm considering tapping and using as added support points.
11 Silverado LTZ - 6.2L/6l80, 2/3 drop, self tuned
85 Hilux - 3RZ, dual cases, caged, 40s, chromo everything
02 TrailBlazer LTZ - 35s, lockers, balls - Gone but not forgotten - Build
User avatar
fishsticks
Moderator
 
Posts: 4356
Joined: Thu Apr 01, 2010 11:30 pm
Location: WA, Vancouver
Name: Donny
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD w/ Aftermarket Locker
Rank: Extreme Offroader

by Zero » Mon Apr 12, 2010 9:02 am

what you did is great! Now you know what to do differently next time, and you should be a bit better or have a understanding of why you had trouble welding the plate. congrats.
Zero
Veteran
 
Posts: 1048
Joined: Thu Sep 10, 2009 5:07 pm
Location: Los Angeles, CA / Toronto, ON
Name: Brendan
Vehicle Year: 2005
Vehicle: Chevrolet Trailblazer EXT
DriveTrain: 4WD w/ G80
Rank: Offroad Rated

by bgwolfpack » Mon Apr 12, 2010 11:43 am

Off-Topic

You guys who weld on a regular basis could really help the rest of us with your knowledge. Would one of you consider a "How to Weld" thread? Just the basics?
bgwolfpack
Veteran
 
Posts: 1794
Joined: Fri Sep 18, 2009 7:19 pm
Name: Randy
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD

by KE7WOX » Mon Apr 12, 2010 1:02 pm

Gordinho80 wrote:Not bad... I wish I could weld!


I wish I could at least have a welder lol.
This is an aggressive post. You probably won’t like it. It is quite doubtful that you have the taste or sophistication to be able to appreciate a post of this quality and depth.

Build Thread
User avatar
KE7WOX
Veteran
 
Posts: 1226
Joined: Tue Sep 29, 2009 2:10 pm
Location: OH, Dublin (Columbus)
Name: Felipe G
Vehicle Year: 2004
Vehicle: Chevrolet TrailBlazer
DriveTrain: 4WD

by Trail X » Mon Apr 12, 2010 1:04 pm

bgwolfpack wrote:Off-Topic

You guys who weld on a regular basis could really help the rest of us with your knowledge. Would one of you consider a "How to Weld" thread? Just the basics?


Have you looked on youtube.com? I saw a few pretty good tutorial videos there.

For example these:



Last edited by Trail X on Mon Apr 12, 2010 1:07 pm, edited 1 time in total.
Reason: Added videos
8-) Build Thread | ExPo Build | YouTube Videos
Not all who wander are lost. -Tolkien
User avatar
Trail X
Founder
 
Posts: 9935
Joined: Mon Sep 07, 2009 10:22 pm
Location: VA, Roanoke
Name: James Downing
Vehicle Year: 2005
Vehicle: Chevrolet TrailBlazer
DriveTrain: 4WD w/ Aftermarket Locker
Rank: Expedition Guide

by fishsticks » Mon Apr 12, 2010 1:34 pm

KE7WOX wrote:
Gordinho80 wrote:Not bad... I wish I could weld!


I wish I could at least have a welder lol.


http://www.harborfreight.com/cpi/ctaf/d ... mber=55250

This is what I use. Nothing special...but works for the little I do.

There is a 110volt version also if you're not into wiring a 220v outlet for your welder.




I learned to weld by using the internet to find out some of the technical stuff. Apart from that I just took my cheapo welder and started putting every bit of scrap metal I had around together. You learn what works and what doesn't. It's not too hard. I have the most trouble with thin metals (like sheet metal). Probably because my welder doesn't have a lot of power adjustments. For that spot welding seems to work better for me than trying to lay a bead on it.

For structural type welds (rock sliders come to mind), I have a buddy who welds professionally and has a pro grade welder. I don't know that I'd trust something the weight of my truck was going to sit on to my welder or my skills.
11 Silverado LTZ - 6.2L/6l80, 2/3 drop, self tuned
85 Hilux - 3RZ, dual cases, caged, 40s, chromo everything
02 TrailBlazer LTZ - 35s, lockers, balls - Gone but not forgotten - Build
User avatar
fishsticks
Moderator
 
Posts: 4356
Joined: Thu Apr 01, 2010 11:30 pm
Location: WA, Vancouver
Name: Donny
Vehicle Year: Other
Vehicle: Other Vehicle
DriveTrain: 4WD w/ Aftermarket Locker
Rank: Extreme Offroader

by Hatchet669 » Mon Apr 12, 2010 5:06 pm

ive done mig tig and stick... its something everyone should learn... i really recommend it...

fishsticks.. i like it... welding thick bars to thin sheet is always gunna cause problems lol... mite want to add a hole or 2 for air flow in there... just my 2cents
User avatar
Hatchet669
Trail-Blazer
 
Posts: 257
Joined: Wed Sep 30, 2009 8:23 pm
Location: IL, Worth
Name: Joe
Vehicle Year: 2003
Vehicle: Chevrolet TrailBlazer
DriveTrain: 4WD
Rank: Trail Ready


Return to Fab Work

cron